Guide · Building owners · 3 min read · Updated 17 November 2026
Curtain Wall Leaks: How to Find and Fix Water Ingress
Short answer
Most curtain wall leaks come from failed or displaced gaskets, blocked drainage in transoms, poor seals at junctions with the roof, slabs or other cladding, and damaged or poorly fitted glass units. A specialist traces the source with inspection and controlled water testing, typically costing £750–£2,500 plus access, then carries out targeted repairs such as resealing, gasket replacement, drainage clearing or reglazing.
How curtain walling is meant to keep water out
Most modern curtain walling uses a drained and ventilated design. The outer gaskets and caps stop most rain, but the system assumes some water will get past them. That water is collected in the glazing rebates, drained along the transoms and out through weep slots or drainage paths to the outside. Inner gaskets and the air seal stop it from reaching the inside of the building.
This means a leak is often not where the water appears inside. Water can enter at one point, travel along a transom or down a mullion and emerge several metres away. That is why guessing and applying sealant to the visible stain rarely works, and can make things worse by blocking the drainage paths the system relies on.
Common causes of leaks
Gaskets shrink, harden and pull back from corners over time, especially on sunny elevations. Drainage slots in transoms block with dirt, insects and debris, so water backs up and overflows inwards. Pressure plates can loosen, and caps or seals can be damaged during cleaning or maintenance. Sealed glass units can move on their setting blocks, opening gaps at the edges.
Junctions are a frequent culprit. The interface between curtain walling and the roof, parapet, ground level, slab edges, windows within the system and adjoining cladding relies on membranes, flashings and seals. If these were poorly designed or installed, or have deteriorated, they can let water into the building fabric. Original installation defects are also common, particularly where joints were not sealed correctly.
- Shrunk, hardened or displaced gaskets
- Blocked drainage slots and weep holes
- Loose pressure plates or missing caps
- Failed seals at mullion and transom joints
- Poor membranes and flashings at roof, slab and ground junctions
- Damaged or poorly set glass units
- Sealant applied in the wrong place blocking drainage
How a leak investigation works
A good investigation starts with information. The specialist reviews when leaks occur, such as during wind-driven rain from a particular direction, where water appears, and any history of repairs. They look at drawings if available, then carry out a visual inspection of the affected area inside and out, checking gaskets, caps, drainage, sealants, flashings and glass.
Controlled water testing then isolates the source. Starting low and working upwards, water is applied to specific joints or areas for set periods while someone watches inside. By testing one area at a time, the specialist can pinpoint where water is entering. Industry methods for site water testing are well established, and the result is a written report with photos, findings and recommended repairs.
| Stage | What happens | Why it matters |
|---|---|---|
| Background review | Leak history, weather, drawings | Narrows down likely causes |
| Visual inspection | Gaskets, caps, drainage, seals, glass | Spots obvious defects |
| Controlled water test | Targeted spraying, observed inside | Pinpoints the entry point |
| Opening up | Remove caps or plates where needed | Confirms hidden defects |
| Report | Findings, photos, repair scope | Basis for accurate repair pricing |
Typical repairs
Once the source is known, the repair is usually targeted. Common fixes include clearing blocked drainage paths, replacing or reseating gaskets, re-torquing pressure plates, resealing joints with the right sealant in the right place, repairing or renewing flashings and membranes at junctions, and reglazing units that have moved or failed. Reglazing a single unit typically costs £600–£2,500.
After repairs, the area should be water tested again to confirm the leak has been fixed. Where leaks are widespread across a facade, a broader remedial programme may be needed, such as replacing all outer gaskets on one elevation. In older systems with many failures, a full refurbishment or overcladding study may be worth considering.
Preventing future leaks
Planned maintenance is the most effective prevention. Regular inspections, typically starting from around £600 per visit for a small building, allow drainage to be cleared, gaskets checked and minor defects repaired before they cause leaks. Window cleaning contractors should be briefed not to damage gaskets and caps, and any damage they notice should be reported.
Keep records of inspections, repairs and water tests, along with the system name and drawings if you have them. This history makes future investigations faster and cheaper. When other works happen near the facade, such as roof repairs or new signage, make sure contractors do not damage seals, block drainage or puncture membranes.
Safety and access
Investigation and repair work often happens at height and must be planned and carried out safely under the Work at Height Regulations 2005, using suitable equipment such as mobile elevating work platforms, cradles, scaffold or rope access. The Construction (Design and Management) Regulations 2015 apply to repair and maintenance work as well as new construction.
Access costs are usually extra to the investigation fee and can be significant on tall buildings. Combining leak investigation with other planned facade work, such as cleaning or inspections, can share access costs. Building owners should also consider safety of occupants and the public below during works, with exclusion zones and protection where needed.
Questions people also ask
Why does my curtain wall only leak in heavy rain?
Leaks that only appear in wind-driven rain often point to gasket gaps, blocked drainage or poor junction details that only get overwhelmed under pressure. Wind pushes water into gaps and can stop it draining normally. Controlled water testing that simulates those conditions usually reveals the entry point.
Can I just apply sealant to stop a curtain wall leak?
It is not recommended without investigation. Curtain walling relies on drainage paths, and sealant in the wrong place can block them, trapping water and making leaks worse elsewhere. Find the source first, then repair with the right method and materials.
How much does a curtain wall leak investigation cost?
Typically £750–£2,500 for survey, controlled water testing and a written report, excluding access equipment. Larger or more complex facades cost more. The report allows repairs to be accurately scoped and priced, which usually saves money compared with trial-and-error fixes.
Written and checked by the Curtain Walling team. Read our editorial policy.
More guides
How Much Does Curtain Walling Cost per m² in the UK? 2026 Guide
In the UK in 2026, stick system curtain walling typically costs £450–£850 per m² supplied and installed, and unitised curtain walling £700–£1,300 per…
Stick vs Unitised Curtain Walling: Differences, Pros and Cons
Stick curtain walling is assembled on site from mullions, transoms and glass, costing about £450–£850 per m². It suits low to mid-rise buildings,…
Curtain Walling Regulations UK: Standards, Fire and Building Safety
Curtain walling in the UK is covered by the product standard BS EN 13830, which sets performance characteristics such as air permeability,…
Curtain Walling Maintenance: Inspection Checklist and Costs
Curtain walling needs regular inspection and maintenance to stay watertight and safe. A typical programme includes cleaning glass and frames,…
Get a free curtain walling quote
Tell us what you need and we'll come back with a clear price.
Request a quote