Curtain Walling

Guide · Developers · 3 min read · Updated 17 November 2026

How Much Does Curtain Walling Cost per m² in the UK? 2026 Guide

Short answer

In the UK in 2026, stick system curtain walling typically costs £450–£850 per m² supplied and installed, and unitised curtain walling £700–£1,300 per m². Low-rise shopfront systems start from £400 per m². Reglazing a single unit costs £600–£2,500, leak investigation with water testing £750–£2,500, and a planned maintenance inspection from £600. Specification, height, access and volume drive the final figure.

How Much Does Curtain Walling Cost per m² in the UK? 2026 Guide

Typical curtain walling prices

Curtain walling is priced per square metre of facade for new installations, and per item or per visit for repairs and maintenance. The rate depends heavily on the system type, the glass and panel specification, the height of the building, how the facade will be accessed and the total area. Larger, repetitive facades usually achieve a lower rate per square metre because design, fabrication and installation are more efficient.

The table gives typical 2026 guide prices. New-build rates assume a standard double-glazed specification on a typical commercial building. Triple glazing, solar control coatings, large-format glass, bespoke colours, integrated doors, opening vents and brise soleil all add to the cost.

WorkTypical 2026 priceNotes
Stick system curtain walling£450–£850 per m²Supply and install, low to mid-rise
Unitised curtain walling£700–£1,300 per m²Factory-made panels, taller buildings
Low-rise shopfront curtain wallingfrom £400 per m²Capped system, excludes doors and operators
Single unit reglazing£600–£2,500Glass, labour and basic access
Leak investigation and water test£750–£2,500Survey, testing, report; access extra
Planned maintenance inspectionfrom £600Per visit, small building

What drives the cost per square metre

System choice sets the baseline. Stick systems are assembled on site from individual mullions and transoms, which keeps fabrication costs down but needs more site labour and scaffold or access time. Unitised systems are built and glazed in a factory, then lifted into place, which costs more per square metre but reduces site time and suits tall buildings and tight programmes.

Glass is the next big item. Larger panes, triple glazing, laminated inner panes, solar control coatings and acoustic glass all increase the cost and the weight the framing must carry. Insulated spandrel panels, shadow boxes and opaque glass at floor zones add cost too. Bespoke mullion depths, deep caps, feature fins and non-standard colours push prices up further.

  • Stick or unitised system
  • Building height, wind loading and exposure
  • Glass size, build-up and coatings
  • Spandrel panels, shadow boxes and fire-stopping details
  • Doors, opening vents and smoke vents within the facade
  • Access method: scaffold, mast climbers, cranes or platforms
  • Total facade area and repetition of panel types

Design, testing and compliance costs

Curtain walling is a designed system, not an off-the-shelf product. The contractor or system supplier carries out structural calculations for wind loads and deflection, thermal modelling, condensation risk analysis and detailed interface design with the frame, slab edges, roof and other cladding. These design costs are usually built into the per-square-metre rate but can be significant on complex projects.

Testing adds cost on larger schemes. Many projects specify performance testing of a sample section, and site water testing of completed areas, to confirm air tightness, watertightness and wind resistance. On relevant buildings at least 18 metres high in England, the materials in the external wall are restricted under Regulation 7(2) of the Building Regulations, and higher-risk buildings go through the Building Safety Regulator, which adds design, documentation and approval time.

Access and programme

Access can make up a large share of the cost, especially on refurbishments and repairs. Stick systems are typically installed from scaffold or mast climbing work platforms. Unitised panels are lifted by tower crane or mini crane and fixed from inside the building, which can reduce external access needs. Repairs on existing buildings may use cradles, mobile elevating work platforms, abseil teams or scaffold, depending on height and the building's setup.

Programme matters too. A facade that needs to be watertight quickly so internal trades can start may justify a unitised system despite the higher rate. Phased work around an occupied building, out-of-hours lifting or road closures for cranes all add cost. Planning access early often saves money, because it lets the contractor choose the most efficient method.

Repair and maintenance budgets

Existing curtain walling needs periodic attention to stay watertight. Gaskets and seals age, drainage paths in transoms block with debris, and sealed glass units eventually fail. Reglazing a single unit typically costs £600–£2,500, with large or high-level units at the top end because of handling and access. Leak investigations including controlled water testing cost £750–£2,500, excluding access equipment.

A planned maintenance programme, with inspections from around £600 per visit for a small building, helps catch small problems before they become expensive leaks or glass failures. For larger facades, maintenance is priced on area and access. Building owners should budget for ongoing maintenance and periodic reglazing as part of the facade's lifecycle cost, rather than waiting for failures.

Getting accurate quotes

For new work, contractors will need architectural drawings, the performance specification, structural information and the programme. The more complete the design information, the more accurate the quote. Ask each bidder to confirm the system they propose, glass build-ups, U-values, any testing included, access assumptions, design responsibility and what is excluded, such as fire-stopping, brackets or interfaces with other trades.

For repairs, provide photos, the building's height and location, any known system name and the history of leaks or breakages. A site survey is usually needed to confirm glass sizes, system type and access. Compare quotes on scope as well as price, because cheaper bids sometimes leave out access equipment, out-of-hours work or making good.

Questions people also ask

Is unitised curtain walling more expensive than stick?

Usually, yes, per square metre. Unitised systems typically cost £700–£1,300 per m² against £450–£850 for stick systems, because panels are fabricated and glazed in a factory. They reduce site time and scaffold needs, so on tall buildings and fast programmes the overall project cost difference can be smaller.

What is the cheapest type of curtain walling?

Capped stick systems on low-rise buildings with standard glass are generally the most economical, with shopfront-style systems starting from around £400 per m². Costs rise with height, larger glass, bespoke finishes, opening vents, doors and enhanced thermal or acoustic performance.

How much does it cost to replace a curtain wall glass unit?

Typically £600–£2,500 per sealed unit, including glass, labour and basic access. Large units, high-level panes, structural glazing and units needing cranes, cradles or abseil teams cost more. Replacement units are made to order, so the opening may need temporary protection meanwhile.

Written and checked by the Curtain Walling team. Read our editorial policy.

Get a free curtain walling quote

Tell us what you need and we'll come back with a clear price.

Request a quote